What Is Box Fill and Why Does NEC Article 314 Require It?

Box fill is the total volume occupied by conductors, devices, and fittings inside an electrical box. NEC Article 314 requires all components to fit within the box's rated volume to prevent overheating, reduce insulation damage, and ensure a safe, code-compliant installation.

NEC Box Fill Requirements — What Article 314.16 Says

NEC Article 314.16(B) assigns volume allowances per component: ungrounded (hot) conductors count as 2.0× their conductor volume each; grounded (neutral) conductors as 1.0× each; all EGCs combined as 1.0× the largest EGC volume; each device or yoke as 2.0× the largest conductor volume; and all internal cable clamps together as 1.0× the largest conductor volume.

How to Use This NEC Box Fill Calculator

Select your box type from the NEC Table 314.16(A) dropdown, then enter the AWG size and count for hot conductors, neutrals, and grounds. Enter the number of devices (receptacles or switches) and toggle on cable clamps if present. Click Calculate for an instant PASS/FAIL result with a full fill breakdown per NEC Article 314.16.

Box Fill Volumes by Conductor Size (NEC Table 314.16(B))

NEC Table 314.16(B) lists conductor volume allowances in cubic inches by AWG size: #18 = 1.50 in³, #16 = 1.75 in³, #14 = 2.00 in³, #12 = 2.25 in³, #10 = 2.50 in³, #8 = 3.00 in³, and #6 = 5.00 in³.

What Counts Toward Box Fill? (Conductors, Devices, Clamps, Ground Wires)

Items that count toward NEC box fill include each ungrounded (hot) conductor, each grounded (neutral) conductor, all equipment grounding conductors counted as one unit, each device or yoke on a strap, and all internal cable clamps counted as one unit. Conductors that both originate and terminate entirely inside the box are not counted.

How to Choose the Right Electrical Box Size

Calculate total required fill using NEC Article 314.16(B), then select a box from NEC Table 314.16(A) with a rated volume equal to or greater than your required fill. Common choices are 4" square boxes (18–30.3 in³) for junction boxes and 3"×2" device boxes (7.5–18 in³) for outlets and switches. Always leave headroom for future circuit modifications.

Frequently Asked Questions About NEC Box Fill

Common NEC box fill questions include: Do spliced conductors count? Yes — each conductor entering the box counts once regardless of splices. Do fixture wires count? Conductors 4 AWG or smaller that do not leave the box are exempt per NEC 314.16(B)(1). For mixed AWG sizes, calculate each conductor group separately and sum the totals. Always use the largest conductor volume in the box for device and clamp allowances.

⚡ Electrical Calculator

NEC Box Fill Calculator

NEC Article 314.16 — Calculate box fill requirements instantly. Instant PASS/FAIL verdict with exact code citation.

📦 Electrical Box

Box Type (NEC Table 314.16(A))

⚡ Conductors & Components

Hot Conductors Ungrounded — 2.0× each

4.00 in³

Neutral Conductors Grounded — 1.0× each

2.00 in³

EGC / Grounds All count as 1× largest

2.00 in³

Devices Receptacles/switches — 2.0× largest

4.00 in³

Internal Cable Clamps All clamps count as 1× largest conductor volume

Please check your inputs and try again.

Calculations per NEC Article 314.16(B) and conductor volumes per NEC Table 314.16(B). Conductors that originate and terminate entirely inside the box are not counted. Device fill uses the largest conductor volume entering the device yoke. Results are indicative — always verify with a licensed electrician before installation.

Voltage Lab

NEC Box Fill Calculator

ABOUT US

Tools

FOLLOW US